U.S. Code · Título 19
Scope of softwood lumber importer declaration program
19 U.S.C. § 1683b
Office of the Law Revision Counsel · release 119-142
Se muestra el texto operativo de la sección. Las notas estatutarias y el historial de enmiendas están en la fuente oficial.
Products included in program
The following products shall be subject to the importer declaration program established under section 1683a of this title:
In general
All softwood lumber and softwood lumber products classified under subheading 4407.10.00, 4409.10.10, 4409.10.20, or 4409.10.90 of the HTS, including the following softwood lumber, flooring, and siding:
Products continually shaped
Any product classified under subheading 4409.10.05 of the HTS that is continually shaped along its end or side edges.
Other lumber products
Except as otherwise provided in subsection (b) or (c), softwood lumber products that are stringers, radius-cut box-spring frame components, fence pickets, truss components, pallet components, and door and window frame parts classified under subheading 4418.90.46.95, 4421.90.70.40, or 4421.90.97.40 of the HTS.
Products excluded from program
The following products shall be excluded from the importer declaration program established under section 1683a of this title:
Exceptions for certain products
The following softwood lumber products shall not be subject to the importer declaration program established under section 1683a of this title:
Stringers
Stringers (pallet components used for runners), if the stringers—
Box-spring frame kits
In general
Box-spring frame kits, if—
the kits contain—
Packaging
Any kit described in subparagraph (A) shall be individually packaged, and contain the exact number of wooden components needed to make the box-spring frame described on the entry documents, with no further processing required. None of the components contained in the package may exceed 1 inch in actual thickness or 83 inches in length.
Radius-cut box-spring frame components
Radius-cut box-spring frame components, not exceeding 1 inch in actual thickness or 83 inches in length, ready for assembly without further processing, if radius cuts are present on both ends of the boards and are substantial cuts so as to completely round 1 corner.
Fence pickets
Fence pickets requiring no further processing and properly classified under subheading 4421.90.70 of the HTS, 1 inch or less in actual thickness, up to 8 inches wide, and 6 feet or less in length, and having finials or decorative cuttings that clearly identify them as fence pickets. In the case of dog-eared fence pickets, the corners of the boards shall be cut off so as to remove pieces of wood in the shape of isosceles right angle triangles with sides measuring ¾ of an inch or more.
United States-origin lumber
Lumber originating in the United States that is exported to another country for minor processing and imported into the United States if—
Softwood lumber
Any softwood lumber or softwood lumber product that originated in the United States, if the importer, exporter, foreign processor, or original United States producer establishes to the satisfaction of U.S. Customs and Border Protection upon entry that the softwood lumber entered and documented as originating in the United States was first produced in the United States.
Home packages or kits
In general
Softwood lumber or softwood lumber products contained in a single family home package or kit, regardless of the classification under the HTS, if the importer declares that the following requirements have been met:
The package or kit contains—
Additional documentation required for home packages and kits
In the case of each entry of products described in clauses (i) through (iv) of subparagraph (A) the following documentation shall be retained by the importer and made available to U.S. Customs and Border Protection upon request:
Products covered
For purposes of determining if a product is covered by the importer declaration program, the President shall be guided by the article descriptions provided in this section.
(June 17, 1930, ch. 497, title VIII, § 804, as added Pub. L. 110–246, title III, § 3301(a), June 18, 2008, 122 Stat. 1848.)